Raypak 337A Instructions d'exploitation

INSTALLATION & OPERATING INSTRUCTIONSSWIMMING POOL & SPA HEATER D-2Catalog No. 6000.57.1F Effective: 04-30-14 Replaces: 12-13-11 P/N 241243 R

10U.S. Installations 1 Canadian Installations 2 A Clearance above grade, veranda, porch, deck, or balcony 1 ft (30 cm) 1 ft (30 cm) B Clearance to w

11VENTING (Continued)

12VENTING (Continued)

13VENTING (Continued)

14VENTING (Continued)

15SEQUENCE OF OPERATIONOn call for heat, the PC board will go through its safety chain (water pressure switch, high limit 1 & 2, roll-out,etc.).

16WIRINGThe D-2 Power Vent includes a wire harness which provides quick connections with the respective controls inthe appliance control box. The har

17WIRING (Continued)STEP 1: VERIFY CURRENT CONNECTIONSAS SHOWN BELOW.P/PVC/M/MVMVPVR/BKY/BKY/BKV/BKV/BKV/BKY/BKG/BKP41RELAYD-2 POWER VENTY/BKHONEYWEL

18WIRING (Continued)MODELS 206, 266, 268, 336, 406, 408 EQUIPPED WITH HONEYWELL GAS VALVEV/WV/BKV/BKG/BKR/BK1P4D-2 POWER VENTP/PVC/M/MVMVPVHONEYWELLVA

19WIRING DIAGRAM – MODELS 207A, 267A, 337A, 407A

2Rev. 5 reflects the following: Changes to: Photo on page 1, “Receiving Equipment” on page 3, “Dimensions” drawing on page 4, Illustrated Parts List o

20WIRING DIAGRAM – MODELS 206A, 266A, 336A, 406A

21WIRING DIAGRAM – MODELS 268, 408

22REPLACEMENT PARTSNOTE: To supply you with the correct part, it is impor-tant that you supply the heater model number, serialnumber and type of g

23Call Out Description 206/207 266/267/268 336/366 406/407/4081 DPDT Relay 008784F 008784F 008784F 008784F2 Blower 008156F 008156F 008156F 008156F3 N.

24www.raypak.com Raypak, Inc., 2151 Eastman Avenue, Oxnard, CA 93030 (805) 278-5300 Fax (805) 278-5468Litho in U.S.A.

3RECEIVING EQUIPMENTOn receipt of your equipment, it is suggested that you visually check for external damage to the carton.If the carton is damaged,

4INSTALLATION REQUIREMENTSFailure to install, maintain and/or operate the Power Vent in accordance with manufacturer’s instructionsmay result in condi

5INSTALLATION1. Start off by disconnecting main power to the heater.2. Remove the front door from the heater. See Fig. 1.3. If this is a retro-fit ap

6INSTALLATION (Continued)6. Lower the jacket top back onto the heater and reinstall the (6) Phillips screws. See Fig. 3.7. If installing on a model 2

7INSTALLATION (Continued)13. Install the right side outdoor conduit through the top 7/8” hole located on the right side of the heater. See. Fig. 13.

8INSTALLATION (Continued)17. Remove the (4) Phillips screws that hold the control panel to the heater and lower the control panel. SeeFig. 17.18. Rem

9VENTINGThe D-2 Power Vent operates with a positive vent static pressure and with a vent gas temperature that preventsexcessive condensate production