Raypak P-R185BL to P-R405BL Manuel d'utilisateur télécharger pdf (Page 30)

PROGRAM MODE BUTTON

Notice to owner- Thermostat operation

Your heater is equipped with a microprocessor controlled thermostat that controls the pool or spa temperature

by measuring the temperature of the water coming back through the heater. It will then monitor the water

temperature and turn the heater back on when it senses that the water temperature is falling below the set point.

It is normal to experience small fluctuations in the return water temperature during the operation of the heater.

The thermostat is calibrated with a very close tolerance to ensure accuracy of the set temperature. Thus, slight

fluctuations in water temperature may cause your heater to cycle on and off frequently. This

phenomenon is not a problem. It will not harm the heater nor interfere with its function to precisely control the

temperature of the pool or spa.

THERMOSTAT CONTROL OPERATION

The pool heater thermostat on the upper front panel of

the heater controls the pool/spa water temperature. This

control center contains a mode button, up and down

temperature adjustment buttons, and a LCD display.

Mode Button

The MODE button functions as a means to turn the

heater off or on in either the pool or spa temperature

setting. The LCD display indicates the mode the heater

is in and the actual water temperature.

Temp Buttons

If the mode is in POOL or SPA, the desired pool or spa

temperature will also be displayed and may be changed

using the UP or DOWN buttons. A manual toggle switch

is also provided right below the MODE button to allow

the heater to be turned off.

Operation

In the POOL or SPA modes, the actual water temperature

is displayed along with the desired pool or spa

temperature. If the heater is firing, a flame icon will be

visible.

To adjust the desired pool or spa temperature setting,

make sure the control is in the appropriate mode (POOL

or SPA) and push the UP or DOWN buttons to get the

desired set point temperature.

LCD DISPLAY TEMP

BUTTONS

MODE

BUTTON

Set Points

The electronic thermostat cannot be set above selected

maximum set points. The maximum default set points

are factory set at 104°F for both pool and spa. These

can be changed to a higher or lower value to suit your

needs, but can never be set above 107°F.

Program Mode Button

To adjust the set point, press the Mode button until the

display reads OFF. Remove the four screws holding the

control cover on. Swing control panel down so the back

side of the board is visible (see page 27). Locate the

Program Mode button as show in figure 9481.

Hold this button and use the Mode button to select “Set”

on the digital display. You can release the button once

“Set” appears. Using the “Up” and “Down” buttons will

change the Maximum Temperature Setting. The control

can be set for a maximum of 107°F. A separate value

can be set for either Pool or Spa by using the Mode

button to select Pool or Spa and using the “Up” and

“Down” arrows to select the desired Max temp for each.

Once this is done reassemble the control panel.

Fahrenheit vs Centigrade

The digital display is capable of displaying Centigrade

as well as Fahrenheit temperatures. To change the

display follow the instruction above to access the

Program Mode Button. Hold this button and use the

Mode button to select “F/C” on the digital display. The

“Up” and “Down” buttons will select “F” or “C” on the

temperature display. Once this is done reassemble the

control panel.

Fig #9481

Fig #9480

DIGITAL THERMOSTAT CONTROLS

DISPLAY

call for heat

FLAME ICON

SET POINT

TEMPERATURE

MODE

POOL or SPA

WATER

TEMPERATURE

Fig# 9484

1 2 ... 25 26 27 28 29 30 31 32 33 34 35 ... 51 52

Commentaires sur ces manuels

Pas de commentaire

Raypak P-R185BL to P-R405BL Manuel d'utilisateur Page 30

Commentaires sur ces manuels

Produits connexes et manuels pour Équipement pour l'eau Raypak P-R185BL to P-R405BL