Raypak B6000 Spécifications Page 1

T-2Raypak B6000 Metasys™ N2System Protocol InterfaceT-2 Communications InterfaceRaypak B6000 Boiler Controllerto Johnson Controls Metasys N2 Interface

APPENDIX AMetasys Point Mapping10

Raypak Controller N2 RegistersRaypak Metasys Register AssignmentsAnalog ParmOutput Offset DescriptionAO1 28 Setpoint Day Setup (Desired water temp @ 7

Raypak Controller N2 RegistersRaypak Metasys Register AssignmentsAnalog ParmInput Offset DescriptionAI 1 60 Outdoor Temperature + 35AI 2 61 Water Temp

Raypak Controller N2 RegistersAI 51 127/128 Boiler Valve Down Times (Sec) #1AI 52 129/130 Boiler Valve Down Times (Sec) #2AI 53 131/132 Boiler Valve D

Raypak Controller N2 RegistersRaypak Metasys Register AssignmentsBinary ParmOutput Offset DescriptionBl 1 58/0 Bit 0 = Night setback present Night Se

Raypak Controller N2 RegistersBl 50 75/0 Boiler Not On Line Boiler #5Bl 51 /1 OK - Boiler OperationBl 52 /2 Low Water outoffBl 53 /3 Low P

T-2 (Raypak B6000 Metasys N2 System Protocol Interface)ContentsQuantityT-2 1EPROM (CPX.XNMn) in small black ESD box 1Check packaging for damage or mis

T-2 INSTALLATION AND MOUNTINGT-2 Module should be mounted on a permanent base not subject to vibrations, moisture or dust. It should be readily acces

WIRING 1500 - RPK1. Open front door of System Protocol Interface Gateway Enclosure.2. Remove Four Screws and the lower cover, revealing the field wiri

B6000 SYSTEM CONTROL BOARD19EPPROM, U4

TABLE OF CONTENTS 1.0 Product Specifications ...

20CHECK YOUR POWER SOURCECIRCUIT BREAKER PANELAC 108 Volts AC Minimum, 132 Volts MAXAB = 108 Volts AC Minimum, 132 Volts MAXBC = Must be less than 1.

APPENDIX BCommunication CableConnection Diagrams21

22

Raypak, Inc., 2151 Eastman Avenue, Oxnard, CA 93030 (805) 278-5300 FAX (805) 278-5489Litho in U.S. A.www.raypak.com

1. Product SpecificationsThe Raypak Gateway card is a hardware product designed to be a communications front end for the RaypakB6000 Boiler Control an

2.0 Metasys Slave Port Functionality2.1 N2 Slave CommunicationsThe Comminications Interface card supports the Johnson Controls Metasys™ N2 Protocol, a

Writing AttributesThe data object attributes can be configured by a master using thefollowing commands:2/1 Write Analog Input Attributes2/2 Write Bina

3.0Hardware Setup3.1 1500 Interface Card Setup3.1.1 Connecting Power to the T-2 CardThe T-2 Card requires an external source of DC voltage. Th

7The parameters are defined as follows:Baud Rate: The baud rate at which the module is to operate.The baud rate is configured as follows:Value Baud Ra

4.0 N2 System Protocol SupportThe Raypak T-2 card supports several data read and write commands for the N2 System protocol. Thedecision on which comma

5.0 DiagnosticsSeveral hardware diagnostics capabilities have been implemented using the LED indicator lights on thefront of the 1500 card. The possi